中国广东省东莞市凤岗镇玉湖路9号B栋8F
anja@flsrfidpro.com+852 46090773
在 24 小时内回复
PPS RFID 标签系列
PPS RFID 标签系列
PPS RFID 标签系列
+

PPS RFID 标签系列

PPS industrial RFID tag for non-metal surfaces: ISO-15693 at 13.56 MHz with a Fujitsu MB89R118C and 2K FRAM, ø30 × 3 mm disc, IP68, -40 to 85 °C continuous and -60 to +220 °C short excursions, resistant to acids, alkalis, solvents and plating baths.

Category工业 RFID 标签
Views1,262
Total Sold444,255
SpecificationStandard PPS disc, MB89R118C, black, screw or adhesive fixing / High-temperature PPS disc, MB89R118C, black, high-temp adhesive
Price联系询价
Download Specification
ItemSpecificationNote
协议ISO-1569313.56 MHz 高频标准
Frequency13.56 MHzHF
ChipMB89R118C-2K (Fujitsu)FRAM memory
内存2K FRAM;支持超过10亿次擦写循环数据在工艺加热过程中保持
应用表面Non-metal surfacesMetal mount not offered on this disc
读取范围1–60 mm(固定读取器)Depends on antenna and reader/writer
尺寸ø30 mm × 3 mm thick, 5 mm centre holeFits a fixture or a machined part
材质PPS (polyphenylene sulfide)高温工程塑料
颜色黑色;其他颜色可定制—
安装Screw through the centre hole or adhesive backingHigh-temp adhesive for oven cycles
重量4 g—
防护等级IP68Dust-tight and immersion resistant
耐化学性酸、碱、溶剂、电镀液Confirm with a sample for your bath
存储温度-40 至 105 °C—
工作温度-40 至 85 °CContinuous
Application temperature-60 至 +220 °CShort excursions; confirm dwell time

构建选择

BuildChip / frequency材质Mounting最佳用途
标准 PPSMB89R118C, 13.56 MHzPPS,黑色Screw or standard adhesivePaint, coating, washing, general chemical exposure
高温 PPSMB89R118C, 13.56 MHzPPS,黑色高温胶粘剂或螺丝重复烤箱循环和长时间保温
仅螺丝组装MB89R118C, 13.56 MHzPPS,黑色Centre-hole screw夹具、工装与货架
Marked buildMB89R118C, 13.56 MHzPPS, laser marked已下单炉后序列号、二维码或颜色编码

Factory inspection sheet

CheckPass criteria失败时操作
Read test在约定的读写器和天线上,读取范围为 1–60 毫米。Re-test the batch; scrap failed units
Heat cycleNo deformation or colour shift after the agreed oven cycle删除批次
Centre hole5 毫米直径,无毛刺,螺丝可自由旋入Reject the unit
尺寸ø30 mm within ±0.2 mm, thickness within ±0.2 mmReject the batch
标记Legible after the heat cycle, correct serialRe-mark or scrap

Application scenarios

涂层前的预处理与干燥

A part that is about to be coated passes through cleaner, rinse and a drying oven. The PPS disc rides on the jig or the part, survives the heat and the chemistry, and is read at the oven exit by a fixed HF reader a few centimetres away, so the right coating recipe follows the right part.

Metal parts hanging on a conveyor through a coating line

Chemical and plating lines

Plating racks and jigs are dipped, rinsed and reused. A PPS tag screwed to the rack carries the rack number and the process route, and keeps working after the bath that would strip a paper label or soften an ABS housing.

Plating tanks and suspended jigs in an electroplating workshop

Tool and fixture tracking at the machine

Fixtures, gauges and tool holders are small, valuable and constantly moving between stations. A 30 mm disc screwed to the fixture is read at a desktop or gate reader as the fixture is loaded, so the machine knows which fixture is in place without an operator scanning a label.

When the tag has to survive the process, not just the warehouse

A tag that works in a warehouse often fails at the next station: the paint line, the plating bath, the drying oven. The PPS RFID Tag Series is built for that next station. The housing is polyphenylene sulfide — a high-temperature engineering plastic that holds its shape and its colour through heat and chemistry that would soften ABS.

标签为直径30毫米、厚度3毫米、中心孔径5毫米的圆盘,重量4克;体积小巧,适用于夹具或机加工部件;防护等级达IP68;基于ISO-15693标准,工作频率13.56MHz,搭载Fujitsu MB89R118C芯片及2K FRAM存储器;该存储器擦写寿命超过10亿次,确保数据在多次工艺循环中持久可靠。

Two black PPS RFID tag discs, front and back view

PPS vs ABS vs ceramic: four dimensions that matter

三种材料覆盖了大多数工业标签。它们不可互换,选择通常取决于四个问题:温度有多高、化学腐蚀性如何、需要多少数量,以及读写器能靠近多远。

PropertyPPSABSCeramicWhat it means on the line
连续温度-40 至 85 °C-30 至 80 °CSimilar range, but brittleAll three handle a normal plant; only two survive a hot process
峰值/应用温度-60 至 220 °C-40 至 100 °CHigh peak, low impact strengthPPS and ceramic take an oven; ABS does not
耐化学性酸、碱、溶剂、电镀液Water, oils, mild detergentsExcellent, but chips and cracksPPS is the practical middle ground
Relative cost中等LowestHighestPPS costs more than ABS, far less than ceramic
Read point1–60 mm(固定读取器)Metres — UHFCentimetres on a fixed readerPPS suits a station reader, not a yard portal
Impact resistanceGoodGood劣质 — 撞击时开裂Dropped tools and fixtures favour PPS over ceramic

简而言之:若标签需留在仓库内并远距离读取,选用 ABS;若仅需耐高温且无物理接触,选用陶瓷;若标签需经过工艺过程且后续仍需处理,则选用 PPS。

Temperature: continuous and peak are different questions

The datasheet has two temperature numbers and they answer different questions. Continuous operation is -40 to 85 °C — the temperature of the room or the line the tag lives in. The application range is -60 to 220 °C — the short excursion of a drying tunnel, a paint cure or a wash. Do not size the tag on the peak alone: a tag that sees 200 °C for two minutes is a different case from one that sits at 150 °C for an hour.

Tell us the cycle — temperature, dwell time, how many times per shift — and we will confirm whether the standard PPS disc is enough or whether the high-temperature build is the safer choice.

Coated metal parts hanging on an overhead conveyor in a paint line

Chemistry: what actually attacks a tag

Water is easy. What kills tags on a finishing line is solvent, acid mist, alkaline cleaner and plating electrolyte — and the failure is usually the adhesive or the print, not the chip. PPS resists the bath itself, which is why the disc is used on plating jigs and racks as well as on the parts. The laser marking is set into the surface so the number stays readable after the chemistry.

如需浸泡标签,请提供浴液成分及停留时间。我们将测试样品,而非承诺耐性表。

电镀车间的长槽与顶部吊具

成本与读取距离:您真正做出的权衡

PPS costs more per tag than ABS, and less than ceramic. In exchange it survives a process that would destroy ABS and does not shatter like ceramic when a fixture is dropped. The compromise is read distance: 13.56 MHz at 1–60 mm on a fixed reader means a station reader at the oven exit, not a 20 m dock door.

That is usually the right trade on a paint or plating line, where the read point is a fixed gate and the tag passes within a few centimetres of the antenna. If the requirement is long-range yard reading, choose a UHF tag such as the ABS or ceramic series and keep the PPS disc for the process step.

Specifying a PPS tag for your line

Standard PPS covers most paint, coating and cleaning processes. The high-temperature build is for longer dwell or repeated oven cycles, where the standard adhesive or marking would degrade first. Both are 30 mm discs with a 5 mm centre hole, so either can be screwed to a fixture or bonded to a part with the same jig.

Send us the process cycle, the bath or solvent, the mounting face and the reader, and we will confirm the build and the fixing. Minimum order, lead time and sample schedule are quoted per project.